Razor Ecosmart metro Instruction Manual download pdf (Page 4)

(cabinet width = 560mm)

note: measurements exclude

the insulating blanket

495mm

405mm

550mm

672mm

Dimension

325mm

130mm

70mm

Metro ﬁreplace inserts are designed to be installed directly

onto a concrete base. An insulating ﬂoor protector is required

toprojectinfrontoftheMetroandmustextendaminimumof

200mm to each side of the door opening making the minimum

ﬂoor protector width 825mm. The minimum ﬂoor protector

projectionforwardofthecavitywallisillustratedinthekey

below. The ﬂoor protector construction must be a minimum

thickness of 26mm Eterpan, or alternative insulating material

of equivalent insulation properties, to achieve the minimum

insulation required. Finish with a non combustible tile or similar.

Floor protector requirements

Position the Metro ECO Smart Insert which is still attached to its

wooden pallet directly in front of the ﬁreplace cavity with the

rear of the insert facing the ﬁreplace opening. The ﬁreplace

insert assembly is bolted to the wooden pallet through its base

panelattwopointsbeingeachfrontcorner.Removeboth

screws and slide the insert into the ﬁreplace cavity taking care

not to mark the ﬂoor protector. Discard the pallet.

1. Attach the fascia with the four longer screws that were

supplied in the plastic bag taking care that the air control

lever passes through the slot provided in the fascia.

Centralise and level the fascia on the ﬁreplace insert

door and secure the four screws.

2. Applying pressure to the door or inside the ﬁreplace

ﬁrebox (not the fascia) carefully manoeuvre the Metro

untiltherearofthefasciaisjusttouchingthefrontfaceof

the ﬁreplace surround. Taking care not to move the

ﬁreplace insert, remove the fascia and mark the position

of the ﬁreplace insert onto the ﬁreplace base.

3. Using a masonry drill, drill into the chimney base through

the two slots which the ﬁreplace insert was secured to

the pallet through, check to ensure the ﬁreplace insert

hasn’t moved and secure using suitable masonry anchors

to comply with the seismic restraint provisions of the

standard.

4. Removethetopbafefrominsidethereplaceinsertand

the removable cabinet top. Check that the ﬂue stub of the

ﬁreplace insert is in line by looking down the chimney, if

not a stainless steel offset or ﬂexi ﬂue will be required.

5. Following the instruction sheet supplied with the ﬂue

system,proceedandttheuewithalljointssealedand

riveted with a minimum of three stainless steel or monel

rivetsoneachjoint.

6. With the ﬂue pipe in position and sealed with a high

temperature ﬁre cement into the ﬂue stub, drill through the

hole provided in the front of the ﬂue stub into the stainless

steel ﬂue pipe and secure with the 6mm bolt and nut

supplied in the plastic bag.

7. Retthetopbafeintotherebox’supperchamber.

Repositiontheremovablecabinettopensuringitis

correctly ﬁtting as detailed on page 2 and secure in its

upperpositionifpossible.Note,iftheadjustableheight

top can be raised slightly but not fully to its upper position,

additional holes should be drilled to enable the top to be

raised to this level.

8. Using a suitable rated insulation (ﬁbretex 450 or similar)

pack any gap that exists between the sides and top of the

ﬁreplace insert cabinet and ﬁreplace surround.

- Do NOT block off the lower convection slots in the base of

the outer wrap (all three sides).

9. Re-attachthefascia,centraliseandlevelwiththedoor

and ensure the air control is moving freely and secure all

four screws.

10. Locate the air control knob which is included in the plastic

bag and carefully work it onto the air control lever.

The Metro is now fully installed and ready for operation but

it is preferable to defer lighting the ﬁre for a day or two if

possibletoallowsealantusedintheuepipejointstoairdry.

Alternatively it is recommended you burn 2-3 sheets of loosely

crumpled newspaper at a time, approx once every hour over

a 6-8 hour period.

Installing your Metro

Fascia Width Height

ECO Smart Insert Fascia 890mm 672mm

FloorProtectorRequirements

Height (Floor Protector) 0mm 10mm 20mm 30mm 40mm

Dimension X 395mm 371mm 353mm 332mm 312mm

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Razor Ecosmart metro Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for Bicycles Razor Ecosmart metro